Chapter 9.10
RESIDENTIAL ZONING DISTRICTS

Sections:

9.10.010    Purpose of chapter, applicability.

9.10.020    Residential district land uses and permit requirements.

9.10.030    Residential district general development standards.

9.10.010 Purpose of chapter, applicability.

A.    Residential zoning districts. This chapter provides regulations applicable to development and new land uses in the residential zoning districts established by Section 9.08.010 (Zoning Districts Established). The purpose of this chapter is to achieve the following:

1.    Ensure the conservation and management of productive agricultural land, the orderly conversion of agricultural lands to urban uses, and provide a consistent and compatible land use pattern;

2.    Ensure the establishment of a network of Urban Villages with centers that serve a network of neighborhoods within the City;

3.    Preserve and enhance the high quality residential setting of the City, while promoting new neighborhoods that provide a balanced mix of land uses and development types that support a small town community character;

4.    Ensure adequate light, air, privacy, and open space for each dwelling;

5.    Minimize traffic congestion and avoid the overloading of public services and utilities; and

6.    Facilitate the provision of public improvements commensurate with anticipated increase in population, dwelling unit densities, and service requirements.

B.    Individual zoning districts. The general development standards for the districts are set forth in Table 2-3. The purposes of the individual residential zoning districts and the manner in which they are applied are as follows:

1.    A (Agricultural) District. The A District identifies areas appropriate for the conservation of productive agricultural lands that can be sustained at an operational level and retain agricultural land in economically viable parcel sizes. The maximum allowable density is one dwelling unit per twenty (20) acres. The A District is consistent with the Agricultural land use designation of the General Plan;

2.    R-R (Rural Residential) District. The R-R District identifies areas appropriate for large lot single-family uses, within a semi-rural environment. The allowable maximum density is one dwelling unit per two (2) acres, with a density range of zero (0) to 0.5 dwelling units per acre. The R-R District is intended to provide for lower density development and small scale agricultural operations. The R-R District is consistent with the Rural Residential land use designation of the General Plan;

3.    R-A, R-1-A, R-1-AH (Single-Family Residential Very Low Density) Districts. The R-A, R-1-A and R-1-AH Districts identify areas appropriate for large lot single-family uses. The allowable maximum density is one dwelling unit per eighteen thousand (18,000) square feet in the R-1-A and R-1-AH Districts and one dwelling unit per twenty-four thousand (24,000) square feet in the R-A District, with a density range of 0.6 to 2.0 dwelling units per acre. The R-A, R-1-A, and R-1-AH Districts are consistent with the Very Low Density Residential land use designation of the General Plan;

4.    R-1, R-1-B, R-1-C (Single-Family Residential Low Density) Zones. The R-1, R-1-B, and R-1-C Districts identify areas appropriate for conventional single-family uses. The allowable density range is 2.1 to 4.0 units per acre, with not more than one dwelling unit per parcel. The R-1, R-1-B, and R-1-C Districts are consistent with the Low Density Residential land use designation of the General Plan when developed within the above density range;

5.    R-1, R-1-MD (Single-Family Residential and Single-Family Residential Medium Density) District. The R-1 and R-1-MD Districts identify areas appropriate for single-family uses, including attached and detached single-family structures. The allowable density range is 4.1 to 7.0 units per acre, with the level of density determined by compliance with performance standards. The R-1 District is consistent with the Low and Medium Density Residential land use designations of the General Plan. The R-1-MD District is consistent with the Medium Density Residential land use designation of the General Plan;

6.    R-1-PRD (Single-Family Planned Residential Development) District. The R-1-PRD District identifies areas appropriate for single-family small lot uses, including attached and detached single-family structures on small lots. The allowable density range is 2.1 to 15.0 units per acre, with the level of density determined by compliance with performance standards. The R-1-PRD District requires a planned development permit. The R-1-PRD District is consistent with the Low, Medium and Medium-High Density Residential land use designations of the General Plan;

7.    R-1-MH (Mobile Home, Single-Family) District. The R-1-MH District is appropriate for residential mobile homes and manufactured housing on individual lots. The R-1-MH District is intended as a single-family planned unit development with individually owned parcels. The allowable density range is dependent on the underlying single-family zoning for each parcel (R-1-18,000 sq. ft., R-1-9,500 sq. ft., R-1-7,500 sq. ft., R-1-6,000 sq. ft.). The R-1-MH District is consistent with the Very Low, Low or Medium land use designations of the General Plan based upon the specific allowed minimum lot size;

8.    R-2, R-2-A (Multifamily Medium-High Density) Districts. The R-2 and R-2-A Districts identify areas appropriate for moderately dense residential uses, including multifamily apartments, duplexes, townhouses, and small parcel, attached and detached single-family uses. The allowable density range is 7.1 to 20.0 dwelling units per acre. The R-2 and R-2-A Districts are consistent with the Medium-High Density Residential land use designation of the General Plan;

9.    R-3, R-3-A (Multifamily High Density) Districts. The R-3 and R-3-A Districts identify areas appropriate for high density residential uses, including attached and detached single-family residential, multifamily apartments and condominiums. The allowable density range is from 20.1 to 30.0 units per acre. The R-3 and R-3-A Districts are consistent with the High Density Residential land use designation of the General Plan;

10.    R-4 (Multifamily Very High Density) District. The R-4 District identifies areas appropriate for high and very high density residential uses, particularly in association with mixed use development. The allowable density range is from 25.1 to 43.0 units per acre, and up to forty-three (43) dwelling units per acre in association with mixed use or transit oriented development. The R-4 District is consistent with the High Density Residential, Mixed Use, and Transit Center land use designations of the General Plan. Very high density developments greater than twenty-five (25) DU/acre up to forty-three (43) DU/acre shall be allowed when specifically called out in the General Plan or in a specific plan; and

11.    MHP (Mobile Home Park, Multifamily) Districts. The MHP District identifies areas appropriate for the accommodation of residential mobile homes and manufactured housing in a mobile home park. The MHP District is intended for multifamily development. The allowable density range is 7.1 to 15.0 dwelling units per acre. The MHP District is consistent with the Medium-High land use designation of the General Plan. (§ 2, Ord. 14-13, eff. October 8, 2014; § 1(2) (Atts. 1, 2), Ord. 20-18, eff. February 3, 2021; § 1(2) (Att. A), Ord. 23-05, eff. August 9, 2023; § 1, Ord. 23-11, eff. November 1, 2023; § 1, Ord. 24-10, eff. July 31, 2024)

9.10.020 Residential district land uses and permit requirements.

A.    Allowed land uses. Table 2-2 identifies the uses of land allowed by this Development Code in each residential zoning district, and the land use permit required to establish each use, in compliance with Division 5 of this title (Land Use/Development Review Procedures).

B.    Prohibited land uses. Any table cell left blank shall mean that the listed land use is prohibited in that specific zoning district.

C.    Site plan review required. Except as otherwise provided in this title, any change of use and all construction activities (e.g., additions, alterations, new construction, reconstruction, or remodeling) shall be subject to site plan review approval as set forth in Chapter 56 of this title (Site Plan Review).

D.    Applicable sections. Where the last column in the tables (“See Section”) includes a section number, the regulations in the referenced section apply to the use; however, provisions in other sections of this Development Code may also apply.

E.    Special review required. A conditional use permit (Chapter 64 of this title, Conditional Use Permits) shall be required for all R-1-PD applications.

F.    Annexation agreement. The uses in Table 2-2 can be modified as set forth in Section 2.1.35 using an annexation agreement approved by the City Council.

G.    Residential Development Review. Notwithstanding anything to the contrary in this title, including subsection C of this section, single-family, multifamily, and the residential component of mixed-use residential housing development projects shall be subject to the applicable residential development standards approved by the City Council and the review process provided in Chapter 77 of this title, as specified.

 

TABLE 2-2
ALLOWABLE USES AND PERMIT REQUIREMENTS
FOR RESIDENTIAL ZONING DISTRICTS 

Land Use (1)

Permit Requirement by District

 

A

R-R

R-A

R-1 (2)

R-2

R-3

R-4

MHP (4)

See Section

Residential

Accessory Residential Dwelling Units

P

P

P

P

 

 

 

 

9.40.020

Accessory Uses and Structures

P

P

P

P

P

P

P

P

9.40.030

Alcohol and Drug Treatment, 6 or Fewer

P

P

P

P

P

P

P

P

9.40.100

Alcohol and Drug Treatment, 7 or More

 

 

 

 

 

C

 

 

9.40.100

Bed and Breakfast Inns

C

C

C

C

C

C

C

 

9.40.050

Boarding Home

 

 

 

 

 

C

 

 

 

Caretaker Housing

P

A

A

 

 

 

 

A

 

Residential (Continued)

Community Apartments and Condominiums

 

 

 

 

C

C

C

 

9.106.030

Convents and Rectories Connected to Religious Institutions/
Facilities

C

C

C

C

C

C

C

 

 

Day Care Home, Large Child and/or Adult

 

P

P

P

P

P

P

 

9.40.080

Day Care Home, Small Child and/or Adult

P

P

P

P

P

P

P

P

9.40.080

Density Bonuses

P

P

P

P

P

P

P

 

9.26.090

Domestic Violence Shelter, Small

A

A

A

A

A

A

A

A

9.40.100

Domestic Violence Shelter, Large

C

C

C

C

C

C

C

C

9.40.100

Emergency Electrical Generators

P

P

P

P

P

P

P

P

9.22.080

Employee Housing, 6 or Fewer

P

P

P

P

P

 

 

 

 

Farmworker Housing, Up to 12 Units or 36 Beds

P

P

P

 

 

 

 

 

 

Group Care Home, 6 or Fewer

P

P

P

P

P

P

P

P

9.40.100

Residential (Continued)

Group Care Home, 7 or More

 

 

 

 

 

C

 

 

9.40.100

Home Occupations

P

P

P

P

P

P

P

P

9.58, 9.40.100

Homeless Emergency Shelter, 7 or More

 

 

 

 

 

C

 

 

9.40.100

Household Pets

P

P

P

P

P

P

P

P

 

Kennels, Private

C

C

C

 

 

 

 

 

 

Manufactured Housing

P

P

P

P

P

P

P

P

 

Mobile Housing

 

 

 

 

 

 

 

P

 

Mobile Home Parks

 

 

 

 

 

 

 

P

 

Modular Housing

 

 

 

 

 

 

 

P

 

Multifamily Housing

 

 

 

 

P

P

P

 

Dev. Stds.

Parolee/Probationer Home

 

 

 

 

 

C

 

 

9.40.100

Senior Assisted Living Facility

C

C

C

C

C

C

C

C

 

Single-Family Housing

P

P

P

P

P

 

 

 

 

Single-Room Occupancy

 

 

 

 

 

 

C

 

 

Sober Living Homes, 6 or Fewer

P

P

P

P

P

P

P

P

9.40.100

Sober Living Homes, 7 to 16

 

 

 

 

 

P

 

 

9.40.100

Residential (Continued)

Sober Living Homes, Greater Than 16

 

 

 

 

 

C

 

 

9.40.100

Supportive Housing

P

P

P

P

P

P

P

P

9.40.100

Temporary Uses

TUP

TUP

TUP

TUP

TUP

TUP

TUP

TUP

9.60.020

Tiny Homes

 

 

 

 

 

 

 

P

9.26

Transitional Housing

P

P

P

P

P

P

P

P

9.40.100

Nonresidential

Airports and Aircraft Landing Facilities

C

C

 

 

 

 

 

 

 

Broadcasting Studios

 

C

C

 

 

 

 

 

 

Cemeteries

C

C

C

C

C

C

C

C

 

Medical Services – Hospitals

C

C

C

C

C

C

C

C

 

Medical Services – Extended Care

C

C

C

C

C

C

C

C

 

Mini-Storage Facilities

C

C

C

C

C

C

C

C

9.40.120

Natural Gas and Electric Facilities

C

C

C

C

C

C

C

C

 

Public Utility Facilities

C

C

C

C

C

C

C

C

 

Solar and Wind Generation Facilities

C

C

C

C

C

C

C

C

 

Swimming Schools

 

 

C

 

 

 

 

 

 

Agricultural and Open Space Resources

Agricultural Uses

P

P

P

 

 

 

 

 

 

Agricultural Products, Sale of When Grown on Site

A

 

 

 

 

 

 

 

 

Animal Keeping (Farm) Including Apiaries

P

A

A

 

 

 

 

 

9.40.040

Community Gardens

P

P

A

A

A

A

A

A

 

Open Space

P

P

P

P

P

P

P

P

 

Plant Nurseries

A

A

A

 

 

 

 

 

 

Rifle, Pistol or Archery Ranges

C

C

C

 

 

 

 

 

 

Stables, Commercial

C

C

 

 

 

 

 

 

 

Stables, Private

P

P

P

P (2)

 

 

 

 

9.40.040(C)

Education, Public Assembly, and Recreation

Assembly/Meeting Facilities

C

C

C

C

C

C

C

C

 

Churches

C

C

C

C

C

C

C

C

 

Golf Courses, Country Clubs

C

C

C

C

C

C

C

C

 

Libraries, Public

 

 

 

C

C

C

C

 

 

Parks and Public Playgrounds

P

P

P

P

P

P

P

P

 

Schools, Private

 

C

C

C

C

C

C

C

 

Schools, Public

P

P

P

P

P

P

P

P

 

Stadia

C

C

C

C

C

C

C

 

 

Education, Public Assembly, and Recreation (Continued)

Trails

P

P

P

P

P

P

P

P

 

Communication Facilities

Satellite Dish Antennas

A

A

A

A

A

A

A

A

9.42

Radio and TV Antennas and Transmission

C

C

C

C

C

C

C

C

9.42

Wireless Telecommunication Facilities

A

A

A

A

A

A

A

A

9.42

Key to Permit Requirements

Symbol

Applicable Process

See Chapter

P

Permitted use (3) (5)

9.56

A

Administrative use permit required (5)

9.62

C

Conditional use – Conditional use permit required (5)

9.64

Blank

Use not allowed

 

Notes:

(1)    See Division 8 of this title for definitions of the land uses listed. See Section 9.08.030 (Allowable land uses and permit requirements).

(2)    This column combines all R-1 sub-zones because the allowable land uses are identical, except for the allowance for horses to be maintained in the R-1-AH District on parcels of eighteen thousand (18,000) square feet or larger.

(3)    A Director-approved site plan review shall be required. See Chapter 56 of this title.

(4)    For purposes of Table 2-2, the MHP District also includes the R-1-MHP District when installed in compliance with State law (Government Code Section 65852.3).

(5)    If there is a conflict between Table 2-2 and any written description setting forth allowable uses and permit requirements elsewhere in this title, the written description shall supersede unless it is clearly evident from the record that the contrary was intended. Disputes shall be resolved pursuant to Chapter 2 of this title.

(§ 2, Ord. 14-13, eff. October 8, 2014; § 1 (Atts. 1, 2), Ord. 16-07, eff. May 4, 2016; § 1 (Att. 4), Ord. 17-03, eff. April 19, 2017; § 1 (Att. 3), Ord. 18-19, eff. September 5, 2018; § 2 (Att. C), Ord. 19-05, eff. May 8, 2019; § 1(2) (Atts. 1, 2), Ord. 20-18, eff. February 3, 2021; § 6 (Att. F), Ord. 21-06, eff. December 1, 2021; § 1(2) (Att. A), Ord. 23-05, eff. August 9, 2023)

9.10.030 Residential district general development standards.1

A.    Compliance with Table 2-3 required. New land uses and structures, and alterations to existing land uses and structures, shall be designated, constructed, and/or established in compliance with the requirements in Table 2-3, in addition to the general development standards (e.g., landscaping, parking and loading, etc.) in Division 3 of this title (Development and Operational Standards).

TABLE 2-3
RESIDENTIAL ZONES GENERAL DEVELOPMENT STANDARDS
REQUIREMENTS BY INDIVIDUAL ZONING DISTRICT 

Development Feature

A

R-R

R-A

Minimum Parcel Size

20 acres

2 acres

24,000 sq. ft.

Minimum Parcel Width

250 ft.

110 ft.

110 ft.

Minimum Corner Parcel Width

250 ft.

110 ft.

110 ft.

Minimum Reverse Corner Parcel Width

250 ft.

110 ft.

110 ft.

Minimum Parcel Depth

500 ft.

130 ft.

130 ft.

Maximum (Gross) Density

1 DU/20 acres

1 DU/2 acres

1 DU/24,000 sq. ft. (1.82 DU/1 acre)

Setbacks Required from the Property Line or Adopted Plan Line (1)

Front

35 ft.

35 ft.

35 ft.

Side (Each)

10 ft.

Street Side

25 ft.

Reversed Corner (Street Side)

25 ft. (26)

Rear

20 ft.

Accessory Structures

See Section 9.40.030 (Accessory uses and structures)

Maximum Parcel Coverage

30%

Main Structure – Maximum Height (Whichever Is Less)

35 ft./2-1/2 stories

Accessory Structure – Maximum Height (Whichever Is Less)

See Section 9.40.030 (Accessory uses and structures)

Antennas, Vertical

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Fences/Walls/Hedges

See Section 9.24.060 (Fences, walls, and hedges)

Off-Street Parking

See Chapter 32 of this title (Parking and Loading Standards)

Satellite Antennas

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Notes:

(1)    No main structure shall be erected within fifty feet (50') of a railroad or freeway right-of-way. A garage or carport shall be located not less than twenty feet (20') from any street frontage where the garage door or carport opening faces the street.

(25)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred feet (100'). A cul-de-sac parcel in the R-1-B District shall have a minimum street frontage width of sixty feet (60'). A cul-de-sac parcel in the R-1-AH District shall have a minimum street frontage width of eighty feet (80'). A cul-de-sac parcel in the R-1-A District shall have a minimum street frontage width of fifty feet (50').

(26)    A reverse corner lot may process an administrative use permit (AUP) to construct side yard fencing at five feet (5') from property line. There shall be a ten-foot (10') corner cut off for sight distance visibility.

 

TABLE 2-3
RESIDENTIAL ZONES GENERAL DEVELOPMENT STANDARDS
REQUIREMENTS BY INDIVIDUAL ZONING DISTRICT (Continued)

Development Feature

R-1-A, R-1-AH

R-1-B

Minimum Parcel Size

18,000 sq. ft.

12,000 sq. ft.

Minimum Parcel Width

110 ft. (25)

80 ft. (2)

Minimum Corner Parcel Width

110 ft.

90 ft.

Minimum Reverse Corner Parcel Width

110 ft.

95 ft.

Minimum Parcel Depth

130 ft.

110 ft. (4)

Setbacks Required (1)

Front

35 ft. (5)

35 ft. (5)

Side (Each)

10 ft.

5 ft. (with an aggregate side setback of 20 ft. minimum) (6)

Street Side

25 ft.

20 ft.

Reversed Corner (Street Side)

25 ft. (26)

25 ft. (26)

Rear

20 ft.

20 ft.

Accessory Structures

See Section 9.40.030 (Accessory uses and structures)

Maximum Parcel Coverage (8)

30%

35%

Main Structure – Maximum Height (Whichever Is Less)

35 ft./2-1/2 stories

Accessory Structure – Maximum Height

See Section 9.40.030 (Accessory uses and structures)

Antennas, Vertical

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Fences/Walls/Hedges

See Section 9.24.060 (Fences, walls, and hedges)

Off-Street Parking

See Chapter 32 of this title (Parking and Loading Standards)

Satellite Antennas

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Notes:

(1)    No main structure shall be erected within fifty feet (50') of a railroad or freeway right-of-way. A garage or carport shall be located not less than twenty feet (20') from any street frontage where the garage door or carport opening faces the street.

(2)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred feet (100'). A cul-de-sac parcel shall have a minimum street frontage width of sixty feet (60').

(3)    A parcel with a rear property line abutting a freeway right-of-way shall have a minimum parcel depth of one hundred fifty feet (150').

(4)    A parcel abutting a major or secondary highway shall have a minimum parcel depth of one hundred twenty feet (120').

(5)    A cul-de-sac parcel shall have a minimum front setback of twenty-five feet (25').

(6)    A parcel developed with a side setback of less than seven feet (7'), additions may be made at a side setback no less than five feet (5').

(7)    A corner parcel shall have a minimum street side setback of twenty feet (20'), and reverse corner parcel shall have a minimum street side setback of twenty-five feet (25').

(8)    In single-family residential districts, the Director, through a single-family residential site plan review application, may grant a bonus parcel coverage provision of up to forty-five percent (45%) in compliance with subsection B of this section (Bonus parcel coverage). A particular model home, existing home or subdivision may be granted bonus parcel coverage based upon the provision of amenities identified in subsection B of this section. In single-family residential districts where a cottage home is proposed through the City’s cottage home program, maximum parcel coverage shall be fifty percent (50%) per Planning Area 7 (PA7) development standards.

(25)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred feet (100'). A cul-de-sac parcel in the R-1-B District shall have a minimum street frontage width of sixty feet (60'). A cul-de-sac parcel in the R-1-AH District shall have a minimum street frontage width of eighty feet (80'). A cul-de-sac parcel in the R-1-A District shall have a minimum street frontage width of fifty feet (50').

(26)    A reverse corner lot may process an administrative use permit (AUP) to construct side yard fencing at five feet (5') from property line. There shall be a ten-foot (10') corner cut off for sight distance visibility.

 

TABLE 2-3
RESIDENTIAL ZONES GENERAL DEVELOPMENT STANDARDS
REQUIREMENTS BY INDIVIDUAL ZONING DISTRICT (Continued)

Development Feature

R-1-C

R-1 (13)

Minimum Parcel Size

9,000 sq. ft.

6,000 sq. ft.

Minimum Parcel Width

70 ft. (10)

60 ft. (2)

Minimum Corner Parcel Width

80 ft.

65 ft.

Minimum Reverse Corner Parcel Width

85 ft.

70 ft.

Minimum Parcel Depth

110 ft. (11)

100 ft. (4)

Setbacks Required (1)

Front

25 ft.
20 ft. (reverse corner parcels)

20 ft.

Side (Each)

5 ft. (with an aggregate side setback of 14 ft. minimum) (6)

5 ft. each side

Street Side

15 ft. (7)(12)

10 ft. (12)

Reversed Corner (Street Side)

20 ft. (12)(26)

15 ft. (12)(26)

Rear

20 ft.

Accessory Structures

See Section 9.40.030 (Accessory uses and structures)

Maximum Parcel Coverage (8)

40%

40%

Main Structure – Maximum Height (Whichever Is Less)

35 ft./2-1/2 stories

Accessory Structure – Maximum Height

See Section 9.40.030 (Accessory uses and structures)

Antennas, Vertical

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Fences/Walls/Hedges

See Section 9.24.060 (Fences, walls, and hedges)

Off-Street Parking

See Chapter 32 of this title (Parking and Loading Standards)

Satellite Antennas

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Notes:

(1)    No main structure shall be erected within fifty feet (50') of a railroad or freeway right-of-way. A garage or carport shall be located not less than twenty feet (20') from any street frontage where the garage door or carport opening faces the street.

(2)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred feet (100'). A cul-de-sac parcel shall have a minimum street frontage width of fifty feet (50').

(3)    A parcel with a rear property line abutting a freeway right-of-way shall have a minimum parcel depth of one hundred fifty feet (150').

(4)    A parcel abutting a major or secondary highway shall have a minimum parcel depth of one hundred twenty feet (120').

(5)    A cul-de-sac parcel shall have a minimum front setback of twenty-five feet (25').

(6)    A parcel developed with a side setback of less than seven feet (7'), additions may be made at a side setback no less than five feet (5').

(7)    A corner parcel shall have a minimum street side setback of twenty feet (20'), and reverse corner parcel garages shall have a minimum street side setback of twenty-five feet (25').

(8)    In single-family residential districts, the Director, through a single-family residential site plan review application, may grant a bonus parcel coverage provision of up to forty-five percent (45%) in compliance with subsection B of this section (Bonus parcel coverage). A particular model home, existing home or subdivision may be granted bonus parcel coverage based upon the provision of amenities identified in subsection B of this section. In single-family residential districts where a cottage home is proposed through the City’s cottage home program, the maximum parcel coverage shall be fifty percent (50%) per Planning Area 7 (PA7) development standards.

(10)    A parcel siding a freeway right-of-way shall have a minimum width of ninety feet (90'). A cul-de-sac parcel shall have a minimum street frontage width of sixty feet (60').

(11)    A parcel abutting a major or secondary highway shall have a minimum parcel depth of one hundred twenty feet (120'). A parcel with a rear property line abutting a freeway right-of-way shall have a minimum parcel depth of one hundred thirty feet (130').

(12)    Private garages located in the side yard area and facing the street shall be set back at least twenty feet (20') from the property line on the side street and not less than five feet (5') from the rear property line of a reversed corner lot.

(13)    The minimum parcel area shall be designated on the Zone Map for each R-1 parcel, as follows: R-1-24,000 sq. ft.; R-1-18,000 sq. ft.; R-1-9,500 sq. ft.; R-1-7,500 sq. ft.; R-1-6,000 sq. ft.

(25)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred feet (100'). A cul-de-sac parcel in the R-1-B District shall have a minimum street frontage width of sixty feet (60'). A cul-de-sac parcel in the R-1-AH District shall have a minimum street frontage width of eighty feet (80'). A cul-de-sac parcel in the R-1-A District shall have a minimum street frontage width of fifty feet (50').

(26)    A reverse corner lot may process an administrative use permit (AUP) to construct side yard fencing at five feet (5') from property line. There shall be a ten-foot (10') corner cut off for sight distance visibility.

TABLE 2-3
RESIDENTIAL ZONES GENERAL DEVELOPMENT STANDARDS
REQUIREMENTS BY INDIVIDUAL ZONING DISTRICT (Continued)

Development Feature

R-1-MH

R-1-MD

Minimum Parcel Size

Determined by sub-zone classification

4,500 sq. ft.

Minimum Parcel Width

60 ft. (14)

50 ft.

Minimum Corner Parcel Width

65 ft.

50 ft.

Minimum Reverse Corner Parcel Width

70 ft

50 ft.

Minimum Parcel Depth

100 ft.

90 ft.

Setbacks Required (1)

Front

20 ft.

15 ft.
(20 ft. to face of garage door)

Side (Each)

5 ft.

5 ft.

Street Side

10 ft.

10 ft.

Reversed Corner (Street Side)

15 ft. (12)(26)

15 ft. (12)(26)

Rear

20 ft.

15 ft.

Accessory structures

See Section 9.40.030 (Accessory uses and structures)

Maximum Parcel Coverage

40% (8)

45%

Main Structure – Maximum Height (Whichever Is Less)

35 ft./2-1/2 stories

Accessory Structure – Maximum Height

See Section 9.40.030 (Accessory uses and structures)

Antennas, Vertical

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Fences/Walls/Hedges

See Section 9.24.060 (Fences, walls, and hedges)

Off-Street Parking

See Chapter 32 of this title (Parking and Loading Standards)

Satellite Antennas

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Notes:

(1)    No main structure shall be erected within fifty feet (50') of a railroad or freeway right-of-way. A garage or carport shall be located not less than twenty feet (20') from any street frontage where the garage door or carport opening faces the street.

(8)    In single-family residential districts, the Director, through a single-family residential site plan review application, may grant a bonus parcel coverage provision of up to forty-five percent (45%) in compliance with subsection B of this section (Bonus parcel coverage). A particular model home, existing home or subdivision may be granted bonus parcel coverage based upon the provision of amenities identified in subsection B of this section. In single-family residential districts where a cottage home is proposed through the City’s cottage home program, the maximum parcel coverage shall be fifty percent (50%) per Planning Area 7 (PA7) development standards.

(12)    Private garages located in the side yard area shall be set back at least twenty feet (20') from the property line on the side street and not less than five feet (5') from the rear property line of a reversed corner lot.

(14)    A parcel siding a freeway right-of-way shall have a minimum width of eighty feet (80').

(25)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred feet (100'). A cul-de-sac parcel in the R-1-B District shall have a minimum street frontage width of sixty feet (60'). A cul-de-sac parcel in the R-1-AH District shall have a minimum street frontage width of eighty feet (80'). A cul-de-sac parcel in the R-1-A District shall have a minimum street frontage width of fifty feet (50').

(26)    A reverse corner lot may process an administrative use permit (AUP) to construct side yard fencing at five feet (5') from property line. There shall be a ten-foot (10') corner cut off for sight distance visibility.

 

.

TABLE 2-3
RESIDENTIAL ZONES GENERAL DEVELOPMENT STANDARDS
REQUIREMENTS BY INDIVIDUAL ZONING DISTRICT (Continued)

Development Feature

R-1-PRD (15)

MHP

Minimum Parcel Size

Determined during PD approval

3 acres

Minimum Parcel Width

Determined during PD approval

110 ft.

Minimum Corner Parcel Width

Determined during PD approval

110 ft.

Minimum Reverse Corner Parcel Width

Determined during PD approval

110 ft.

Minimum Parcel Depth

Determined during PD approval

130 ft.

Maximum Density

15 DU/acre

15 DU/acre

Setbacks Required

Front

Determined during PD approval

15 ft.

Side (Each)

Determined during PD approval

5 ft.

Street Side

Determined during PD approval

10 ft.

Reversed Corner (Street Side)

Determined during PD approval

15 ft.

Rear

Determined during PD approval

10 ft.

Accessory Structures

See Section 9.40.030 (Accessory uses and structures)

Maximum Parcel Coverage

Determined during PD approval

45%

Main Structure – Maximum Height (Whichever Is Less)

35 ft./2-1/2 stories

35 ft./2-1/2 stories

Accessory Structure – Maximum Height

See Section 9.40.030 (Accessory uses and structures) or determined during PD approval

Antennas, Vertical

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Fences/Walls/Hedges

See Section 9.24.060 (Fences, walls, and hedges)

Off-Street Parking

See Chapter 32 of this title (Parking and Loading Standards)

Satellite Antennas

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Notes:

(15)    An R-1 planned residential development shall require the processing and approval of a planned development permit. See Chapter 66 of this title (Planned Development Permits).

(25)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred feet (100'). A cul-de-sac parcel in the R-1-B District shall have a minimum street frontage width of sixty feet (60'). A cul-de-sac parcel in the R-1-AH District shall have a minimum street frontage width of eighty feet (80'). A cul-de-sac parcel in the R-1-A District shall have a minimum street frontage width of fifty feet (50').

 

TABLE 2-3
RESIDENTIAL ZONES GENERAL DEVELOPMENT STANDARDS
REQUIREMENTS BY INDIVIDUAL ZONING DISTRICT (Continued)

Development Feature

R-2, R-2-A

R-3, R-3-A

Minimum Parcel Size

7,200 sq. ft.

8,500 sq. ft.

Minimum Parcel Width

60 ft. (16)

60 ft. (17)

Minimum Corner Parcel Width

65 ft.

65 ft.

Minimum Reverse Corner Width

70 ft.

70 ft.

Minimum Parcel Depth

120 ft. (3)

120 ft. (3)

Maximum (Gross) Density

20.0 DU/acre
(1 DU/2,180 sq. ft.)

30 DU/acre

(1 DU/1,450 sq. ft.)

Setbacks Required

Front

20 ft.

15 ft.

Side (Each)

5 ft.

5 ft.

Street Side

15 ft. (18)
15 ft. (reverse corner parcel)

10 ft. (18)
15 ft. (reverse corner parcel)

Rear

20 ft.

15 ft.

Accessory Structures

See Section 9.40.030 (Accessory uses and structures)

Maximum Parcel Coverage

45%

Main Structure – Maximum Height (Whichever Is Less)

35 ft./2 stories (19)(20)

45 ft./3 stories (19)(20)

Accessory Structure – Maximum Height (Whichever Is Less)

12 ft./1 story

Antennas, Vertical

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Fences/Walls/Hedges

See Section 9.24.060 (Fences, walls, and hedges)

Off-Street Parking

See Chapter 32 of this title (Parking and Loading Standards)

Satellite Antennas

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Notes:

(3)    A parcel with a rear property line abutting a freeway right-of-way shall have a minimum parcel depth of one hundred fifty feet (150').

(16)    A parcel siding a freeway right-of-way shall have a minimum width of eighty feet (80'). A cul-de-sac parcel shall have a minimum street frontage width of forty feet (40').

(17)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred ten feet (110'). A cul-de-sac parcel shall have a minimum street frontage width of forty-five feet (45').

(18)    A reverse corner parcel shall have a minimum street side setback of fifteen feet (15'), with a minimum of twenty feet (20') to the face of the garage door.

(19)    In the R-2-A and R-3-A Districts, no main structure erected shall exceed one story or twenty feet (20') in height.

(20)    In the R-2 and R-3 Districts, greater main structure height may be granted under a conditional use permit, not to exceed three (3) stories or fifty feet (50') in the R-2 District or sixty feet (60') in the R-3 District.

(25)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred feet (100'). A cul-de-sac parcel in the R-1-B District shall have a minimum street frontage width of sixty feet (60'). A cul-de-sac parcel in the R-1-AH District shall have a minimum street frontage width of eighty feet (80'). A cul-de-sac parcel in the R-1-A District shall have a minimum street frontage width of fifty feet (50').

 

TABLE 2-3
RESIDENTIAL ZONES GENERAL DEVELOPMENT STANDARDS
REQUIREMENTS BY INDIVIDUAL ZONING DISTRICT (Continued)

Development Feature

R-4

Minimum Parcel Size

10,000 sq. ft.

Minimum Parcel Width

65 ft. (110 ft. if siding a freeway)

Minimum Corner Parcel Width

75 ft.

Minimum Reverse Corner Parcel Width

80 ft.

Minimum Parcel Depth

110 ft. (3)(4)

Maximum (Gross) Density

25 DU/acre except where the General Plan allows higher – then 43.00 DU/acre (1 DU/1,000 sq. ft.) (23)

Setbacks Required

Front

15 ft.

Side (Each)

5 ft.

Street Side

15 ft. (21)

Rear

15 ft. (21)

Accessory Structures

See Section 9.40.030 (Accessory uses and structures)

Maximum Parcel Coverage

60%

Main Structure – Maximum Height (Whichever Is Less)

50 ft./4 stories (22)(23)

Accessory Structure – Maximum Height (Whichever Is Less)

12 ft./1 story

Antennas, Vertical

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Fences/Walls/Hedges

See Section 9.24.060 (Fences, walls, and hedges)

Off-Street Parking

See Chapter 32 of this title (Parking and Loading Standards)

Satellite Antennas

See Chapter 42 of this title (Wireless Telecommunication Facilities)

Notes:

(3)    A parcel with a rear property line abutting a freeway right-of-way shall have a minimum parcel depth of one hundred fifty feet (150').

(4)    A parcel abutting a major or secondary highway shall have a minimum parcel depth of one hundred twenty feet (120').

(21)    For a structure exceeding thirty-five feet (35') or two and one-half (2-1/2) stories, the required side and rear setbacks, and distances between structures, shall be increased at the rate of three inches (3") for each foot of height increase.

(22)    Additional height/stories may be allowed, in compliance with Chapter 64 of this title (Conditional Use Permits).

(23)    Where specifically allowed by the Mixed Use Table in the General Plan or by a specific plan, the maximum density shall be as specified in those documents.

(25)    A parcel siding a freeway right-of-way shall have a minimum width of one hundred feet (100'). A cul-de-sac parcel in the R-1-B District shall have a minimum street frontage width of sixty feet (60'). A cul-de-sac parcel in the R-1-AH District shall have a minimum street frontage width of eighty feet (80'). A cul-de-sac parcel in the R-1-A District shall have a minimum street frontage width of fifty feet (50').

B.    Bonus parcel coverage. In Single-Family Residential Districts the Director, through a single-family residential site plan review application in compliance with Chapter 56 of this title, may grant a bonus parcel coverage provision of up to an additional forty-five percent (45%). A particular model home, existing home, or subdivision may be granted the following parcel coverage maximum based upon the provision of the following amenities, not to exceed a maximum of forty-five percent (45%) in compliance with Table 2-3A (Maximum Parcel Coverage Bonus).

 

TABLE 2-3A
MAXIMUM PARCEL COVERAGE BONUS 

Maximum Percent of Bonus Allowed

Additional Amenities

1

Recessing the garage from the front yard setback by at least five feet

1

Constructing a screen enclosure for refuse containers and recycling bins

1

Creation of a unique tree or neighborhood landscape pattern (privately maintained)

1

Creation of significant curvilinear streets throughout the subdivision

2

Enhanced architectural treatment (e.g., greater depth and articulation of front facing architectural elements)

2

Architectural treatment (e.g., embellishment) of all elevations of the proposed home

2

Additional and acceptable privately maintained neighborhood amenities (e.g., sport courts, etc.)

5

Recessing the placement of the garage to the rear of the parcel or the provision of a swing garage where the garage door(s) does not face the street

5

Provision of front, interior, or side yard courtyards/porches of at least 100 square feet

To Be Determined by the Director

Other amenities as approved by the Director which provide a significant additional amenity

(§ 2, Ord. 14-13, eff. October 8, 2014; § 1 (Att. 1), Ord. 16-07, eff. May 4, 2016; § 1 (Att. 4), Ord. 17-03, eff. April 19, 2017; § 1 (Att. 3), Ord. 18-19, eff. September 5, 2018; § 2 (Att. C), Ord. 19-05, eff. May 8, 2019; § 1(2) (Att. A), Ord. 23-05, eff. August 9, 2023; § 2, Ord. 23-11, eff. November 1, 2023; § 2, Ord. 24-10, eff. July 31, 2024)

1

Code reviser’s note: Footnote (25) to Table 2-3 in Section 9.10.030 was not specifically laid out in the amendments of Ord. 16-07 but was added to the Code at the City’s request. This addition conveys the intent of the amendments adopted by Ord. 16-07.